Ref: SHORT S-SERIES

Schleifringübertrager - Kurze Bauform - 4 bis 10 Bahnen - 12000U/min

  • Compact slip ring - end of shaft (axial)
  • Circuit number: 4, 6, 8 or 10
  • Maximum Rotation speed: 12 000 RPM
  • Wire termination to color coded solder terminals and/or quick disconnect circular connectors
  • Maximum Peak Noise: 0.1ohm
  • Lifetime: 100 million revolution
  • Operating Temperature Range: -40°C to 121°C
  • Sealed against dust - permanently lubricated - no maintenance required
  • Stator diameter: 41.3mm - Width: 22-37 mm - Weight: 55-120 g
  • Amplifier TC and PJ available
  • Max current per circuit: 500 mA

Datenblatt herunterladen

Connectez-vous à votre compte pour afficher les prix
Se connecter
?

Most compact slip ring for up to 10 circuit connections

The Short S-Series Slip Ring Assemblies are utilized for a variety of applications requiring up to ten circuit connections within minimum space. The slip rings are designed to mount on the end of a rotating shaft and make electrical connections to strain gages, thermocouples, or other sensors that have been installed on equipments rotating up to 12.000 rpm.

The Short S-Series slip rings are available in 4, 6, 8 and 10 circuit slip ring. Permanently lubricated bearings eliminate the need for routine cleaning and maintenance. The lightweight and compact design of these slip ring assemblies make them ideal for use in applications where limited space is available.

The slip ring brushes and rings are made of precious metals in order to minimize resistance variation and enable the assemblies to be used for low level instrumentation signals. For improved performance, miniature or spinning amplifiers may be installed between the sensors and the rotors. For space limited applications, some models have an embedded amplifier for strain gage based sensor, or thermocouple. For details, please refer to the overview below.

In addition, a stainless steel and aluminum case provides protection from dust and other contaminants.

Installation

The slip rings of the SHORT S Series (SHORT-S4, SHORT-S6, SHORT-S8, SHORT-S10) can be easily mounted to the end of the shaft with two screws. Sensor's wires can either be linked to the surface or to the inside of the shaft. In the second scenario, a wire groove shall be milled across the end of the shaft or adapter. Connections are made through color coded solder terminals located on the slip ring rotor and a connector on the slip ring stator. Redundant terminals are included to provide back-up connections.

No additional setup is required. The slip ring can be mounted and used in any application. Another great feature is the limited space it takes: 19 mm.

Available models

Rotation speed for all models : 12.000 rpm

Model Circuits Rotor Diam [mm] Stator diam [mm] Length [mm] Weight Rotor connection Stator connection Comment
Short S4/X 4 41.28 31.24 22 74g Soldering terminals Connector 3 m cable incl.
Short S4/T 4 41.28 31.24 22 55g Soldering terminals Soldering terminals
Short S4M/X 4 50.77 32.26 22 75g Soldering terminals Connector 3 m cable incl.
Short S4/RX 4 41.28 31.24 26 75g Connector Connector 3 m cable incl.
Short S4/T/TC1 4 41.28 31.24 28 56g Soldering terminals Soldering terminals 1 TC Amplifier (J, K, T)
Short S6/X 6 41.28 31.24 22 Soldering terminals Connector 3 m cable incl.
Short S6/T 6 41.28 32.26 25 75g Soldering terminals Soldering terminals
Short S6/T/TC3 6 41.28 31.24 28 56g Soldering terminals Soldering terminals 3 TC Amplifier
Short S6/T/G 6 41.28 31.24 28 75g Soldering terminals Soldering terminals 1 SG Amplifier
Short S8/X 8 41.28 31.24 27 88g Soldering terminals Connector 3 m cable incl.
Short S8/T 8 41.28 32.26 27 75g Soldering terminals Soldering terminals
Short S8M/X 8 50.77 32.26 27 78g Soldering terminals Connector 3 m cable incl.
Short S8/RX 8 41.28 31.24 33 90g Connector Connector 3 m cable incl.
Short S8/T/TC4 8 41.28 31.24 37 56g Soldering terminals Soldering terminals 4 TC Amplifier
Short S8/T/G 8 41.28 31.24 28 75g Soldering terminals Soldering terminals 1 SG Amplifier
Short S8/X/2G 8 41.28 31.24 37 120g Soldering terminals Connector 2 SG Amplifier. 3m cable incl.
Short S8/T/2G 8 41.28 31.24 37 120g Soldering terminals Soldering terminals 2 SG Amplifier
Short S10/X 10 41.28 31.24 30 90g Soldering terminals Connector 3 m cable incl.
Short S10/T 10 41.28 32.26 30 75g Soldering terminals Soldering terminals
Short S10M/X 10 50.77 32.26 30 78g Soldering terminals Connector 3 m cable incl.

Applications

  • Torque measurements transmission
  • Rear axle measurements
  • Vibration measurements
  • Fan, air conditioning systems qualification
  • Acceleration measurements
  • Brake measurements
  • Gearbox rendering measurements
Ausführung
SHORT-S Series
Picots à souder
Anzahl an Bahnen
4, 6, 8, 10
Betriebstemperatur
-40 zu 121 °C
  • Rotor diameter: 41 mm
  • Stator diameter: 31 mm
  • Length: 21 to 37 mm

Embedded amplifier/encoder

  • Amplifier to connect between the sensor and the slip ring allowing the optimization of the signal's quality
  • Thermocouple: Short S4/T/TC1, Short S6/T/TC3 ou Short S8/T/TC4. Amplifier specifications as AMP-TC-M1.
  • Pont de jauges: Short S6/T/G ou Short S8/T/G ou Short S8/X/2G. Amplifier : AMP-SG-M1.
  • Encoder for speed information transmission - 360°/rev

Cable

  • SHORT S4/X - 3 or 6 m - open lead
  • SHORT S6/X, SHORT S6/X/G and SHORT S6/X/TC3 - 3 or 6 m - open lead
  • SHORT S8/X - 3 or 6 m - open lead
  • SHORT S8/X/2G - 3 or 6 m - open lead
  • SHORT S10/X - 3 or 6 m - open lead
  • Custom wiring (cable length, connectors)
  • Signal conditioning for strain gage
  • Signal conditioning for thermocouple

Verwandte Produkte

collecteur tournant mesure

S-Series

Schleifringübertrager - 4 bis 10 Bahnen - 12000U/min - Montage am rotierenden Wellenende
collecteur tournant mesure

SR Series

Schleifringübertrager - robust - 4, 6, 8, 10, 20, 36 Bahnen
MICROTC -
Amplificateur collecteur tournant bout d'arbre

AMP-TCn-x2

Messverstärker für 1 bis 9 Thermoelemente - für Schleifringübertrager
Telefon +49 176 101 78 292 Kontakt Kontaktformular Newsletter S'inscrire à la newsletter